Coil Over Shock AbsorberShock Absorber Pair 423/272mm AC513001 >

Coil Over Shock AbsorberShock Absorber Pair 423/272mm

Coil Over Shock AbsorberShock Absorber Pair 423/272mm >

Forst Product

Part Code: AC513001

£72.50

Availability: In stock

OR

Description:

Coil-over shock absorber with a chrome plated spring.

SSP coilover is a shock absorber fitted with a chrome plated assistance spring. Most often used on Bajas, buggies and trikes. The lower spring mount allows a small amount of tension adjustment. C spanners are included for adjusting.

It is very important to fit the correct length shocks to a lowered car. There must be at least 2 inches of up and down travel from the normal ride height. To ascertain what length you require you must measure the distance between the shock mountings on your vehicle after you have removed the existing shock. This must be done with the vehcile on its road wheels (not on a jack). Once you have measured you need to check it against te shock absorbers we list to see which ones you need.

Prior to fitting new shock absorbers always pump it through a few strokes the correct way up. This removes bubbles that may have formed in the fluid whilst in storage and improves the effectiveness.

Quality:

Good Quality

Fitting:

423mm extended\/272mm collapsed.

Weight:

4.3953 kg

For Vehicles

Beetle 1947-1979 | Beetle Cabrio 1949-1979 | Karmann Ghia 1955-1974 | T2 Bay 1968-1969 | T2 Split 1950-1967 | Type 3 1961-1975

Product Questions

Sort by ASC
I orten have heavy loads in My 1977 baybus, is this somehung for me?
Regards Mats
11
Question by: mats norr on 22 Jul 2017 19:46:00
They will be too short and the springs are more for aesthetics. These would be better suited:

https://www.vwheritage.com/ac513kg5530-kyb-gas-a-just-shock-t2-rear-565-345mm
Answer by: Ben P (Admin) on 24 Jul 2017 09:26:00
1
I have a stock height bay with old KYB shocks fitted but it is poor in side wind conditions. I fitted coilovers on the front and heavy duty roll bars front and back which helped alot. Do you think a pair of these on the rear would help more? The rear sags by about an inch or so.
2
Question by: john pouney on 11 Jan 2018 21:36:00
In this instance we would probably look at lowering the vehicle slightly with some dropped spindles in the front and a spline adjustment in the rear to help combat the crosswind issue as these modifications will have a much bigger effect than the slightly increased spring rate the coil overs will provide.
Answer by: Eliot Pocock (Admin) on 12 Jan 2018 16:41:00
-12
Could you please tell me the following
The outside diameter of the coil spring?
The top and bottom mount bolt diameter?
1
Question by: neville on 29 Dec 2018 12:15:00
The spring diameter is approx 58mm and will take a bolt with a diameter of 11mm
Answer by: Nick Bitton (Admin) on 31 Dec 2018 09:51:00
2
I have a 1976 Kombi pickup (single cab) and use this to haul generators and equipment. I am looking to beef up the rear suspension a little so that the Kombi sits more level when there is a payload. The current suspension is stock standard. Will these shock assist with raising the rear of the a couple of inches?
1
Question by: Ken on 23 Jan 2018 21:59:00
These coilovers are unlikely to help with what you are trying to achieve. We would suggest some shock such as AC513KG5530 and looking at adjusting the torsion bars as per a workshop manual suggests.
Answer by: Eliot Pocock (Admin) on 24 Jan 2018 16:47:00
15
Hello

Will this fit my A4 B7 2005 model? Looking to replace the rear 2.

Thanks
0
Question by: Mark MacDonald on 30 May 2019 05:40:00
Sorry, these won't fit an A4. Not a model we can help with currently.
Answer by: Nick Bitton (Admin) on 30 May 2019 08:35:00
1
Does those fits Daihatsu Sirion 2006. The two rear shock absorbers are gone?
0
Question by: Biniam on 2 Jun 2019 21:25:00
We only list these for a Volkswagen application, so are unable to say if they would fit a Daihatsu Sirion.
Answer by: Nick Bitton (Admin) on 3 Jun 2019 09:22:00
0