Grease Gun, 4 jaw, 120cc Capacity.

Ideal for axle beams.

Grease Gun adaptor hose.

Ideal for confined areas, flexible hose.

Ball Joint Separator, Scissor Type.

Also works on track rod ends.

Wheel Brace, Telescopic.

For 17/19mm wheel bolts/nuts.

Flexi Funnel.

Ideal for aircooled engine bays.

Tin Snips.

For straight or right hand cuts.

Trim Removal Tool. A 10 in 1 tool for the removal of trims.

Removes, clips, headlamp springs and badges.

Feeler Gauges.

32 piece, metric and imperial blades. Ideal for tappets, points and spark plugs.

Brake spring removal tool.

To align pins, springs and cap washers.

Valve grinding sticks, set of 2.

With 4 sizes of suction cup.

Magnetic Parts Tray.

Keep track of your nuts, bolts, sockets etc.

Alloy Wheel Brush.

Gets into tight spaces, doesn't scratch.

Oil Suction Gun.

Ideal for filling gearboxes.

Kneeling Mat.

Useful for garage, garden and breakdowns.

Track Right Gauge.

Drive over tracking system, simple to use. 1 tonne per wheel capacity.

Exhaust gas tester.

A digital gauge for measuring exhaust CO level. Accurate to 0.5%.

Eezilap, Valve lapping tool.

Attaches to an electric drill.

Adjustable Strobe Gun.

Great for setting a 009 at full advance. With readout for RPM, dwell & advance.

Eezi Bleed.

Brake bleeding tool, uses tyre pressure. Makes brake bleeding a one person job.

Engine Stand - Bench Mounted

Enables engine case to be rotated through 360 degrees. Can also be used for gearboxes.

Engine Assembly Stand

Mounted on castors for mobility.

Engine Dolly

H/D construction mounted on castors for easy mobility.

Universal Flywheel Lock

Fits 6V and 12V flywheels.

Oil Pump Puller

Easy to use, stops pump or engine case damage.

Cam Follower Clips

Holds followers in correct position, essential when re-using with the same camshaft.

Gearbox Drain Plug Socket

Fits 3/8 inch drive ratchet. This also fits the A-arm bush on IRS vehicles.

Gearbox Drain Plug Wrench

This also fits the A-arm bush on IRS vehicles.

Distributor Drive Puller

Removes driveshafts with ease.

Spring Plate Removal Tool

Useful when lowering or adjusting rear suspension. Fits all T1 models.

Oil Piston Puller

Removes seized pressure relief valve pistons.

Adjustable Push Rod

Used for setting correct valve geometry on uprated engines.

Flywheel Dowel Pin Jig

Provides correct position when drilling crankshafts and flywheels for 8 dowel pins.

Crankcase Splitter

Helps free difficult cases. Fits into oil pump aperture.

Crankshaft Pulley Puller

Can be used with the engine in situ.

Airflow Meter

Use this to balance twin carburettor setups

Adaptor for Airflow Meter

Adapts our flow meter to fit the following carbs:

Cylinder Head Assembly Tool

Axle Nut Tool

Eases the removal of stubborn nuts. Apply pressure with a ratchet or bar and hit with a hammer.

36mm Sockets

Useful for flywheel gland nuts and rear hub nuts

46mm Sockets

Breaker Bar

Deluxe Flywheel Seal Installation Tool

Does not require the dowel pins to be removed.

Crank Gear Puller

Splined Socket

For CV joint bolts. Fits 3/8 inch drive.

Chamber Volume

Measures combustion chamber capacity. Supplied with a syringe and three colour-coded plexi-glass discs to fit most bore sizes.

Deck Height Measuring Tool

Accurately check deck height with this tool and a set of feeler gauges.

Oil Filler Nut Tool

Lug Type

For occasional use. Fits 3/8 inch ratchet.

Oil Filler Nut Tool

Internal Type

Grips the inside. For regular use.

Clutch Alignment Tool

A must for any mechanic.

Clutch Alignment Tool

A must for any mechanic.

Helping Hand Tool

Helps steady drums or flywheels whilst loosening stubborn nuts.

Starter Motor Bush Puller

Makes this awkward job easy.

Mr Torque Tool

New Product!

Multiplies leverage from a normal ratchet. For use on flywheel gland nuts and rear hub nuts. Supplied as a complete kit including drum plate, 6 Volt gear and 12 Volt gear.

Crankcase Measuring Tool

Crankshaft Measuring Tool

Coil Spring Compressors

Use these when working on 1302/3 strut assemblies or any car with Macpherson struts.

End Float Tool

Use this to set flywheel end float. For use with feeler gauges.

108 Piece Socket Set

108 Piece socket set. A top quality chrome vanadium socket set including 1/2" drive & 1/4" drive sockets and ratchets plus various screwdriver and other bits.

Heavy Duty Axle Nut Whacker. 36mm Professional quality

Battery Booster/Starter

Will start any petrol engine up to 2.5 litres - 1200 peak amps, 400 amp cranking rate. Up to 30 starts from one charge. Electronic control prevents damaging Voltage spikes. Heavy duty, weatherproof ABS plastic casing.

Heavy Duty insulated cables and clamps. Automatic mains charger and cigarette light charger included.

The easy way to tow your car home. Simply attach an A-Frame, connect to tow ball and you're off. No need for someone to steer or brake in the car being towed. For safety, please check the un-braked towing specification of the car you are using to tow.

A-Frame, Beam Axle T1

Clips to lower axle tube of balljoint beam cars 1965>.

A-Frame, 1302/3

A-Frame attaches to a mounting plate. Can be left in place for ease of later use.

Engine Assembly Lube

Positive protection against scuffing & scoring on initial fire up after a rebuild. 2oz Tube.

Spare Wheel Tool Box

Vintage style

Empi Style

Faithful reproduction of an original accessory that fits into a stock style spare wheel for storage. Choice of 2. Empi logo or Flat 4 VW Logo.

Jacks

Scissor Jack for all models

Upright Jack for T1, T3 and Ghia only